Observations: This experiment was divided into two parts: one part was to observe the properties of a single Alka Seltzer tablet and the second part was to find the percentage of CO2. In the first part of the experiment, the visible properties of Alka Seltzer were observed and recorded. Each Alka Seltzer contains the same three ingredients: 325 mg of Aspirin, 1000 mg of Citric Acid, and 1916 mg of Sodium Bicarbonate.…
In order to safely dispose of a solution with a pH of 12, the solution needs to be diluted with an acid to neutralize the basic solution. The pH range should be between 5 to 8 to be ready for disposal. 2. A graduated cylinder, Erlenmeyer flask, and beaker were used to measure a 60-mL volume. Which of these devices seems to be the most accurate for measuring a 60-mL volume?…
This lab was a two week long lab called the Grignard Reaction lab. The purpose of this lab was to perform the Grignard reaction and to obtain the final product triphenylmethanol from a halide, phenylmagnesium bromide and the starting material, methyl benzoate along with the Grignard reagent. Bromobenzene, magnesium turnings, and anhydrous ether were needed to form the Grignard reagent. To synthesize the reagent, react the reagent with methyl benzoate to form a tertiary alcohol. The objective of the Grignard Reaction lab was to obtain the actual yield of the product, to calculate theoretical and percent yield of the product, and to record the melting point of the product.…
The Effect of Temperatures on Rate of Reaction of Alka-Seltzer Introduction: A. Background This particular experiment consists of a purpose of finding out the effect of various temperatures on the rate of reaction of the Alka-Seltzer tablets. Alka-Seltzer is a medical drug that acts as a pain reliever or an antacid, which helps neutralize stomach acidity, such as heartburn. Alka-Seltzer is a form of a baking soda which is also known as sodium bicarbonate, (NaHCO₃). When sodium bicarbonate (NaHCO₃) comes in contact with water (H2O), the compound dissociates into two different ions: sodium (Na+) and bicarbonate (HCO₃-) ions.…
Investigating Properties Lab Ishan Godra SCH4U Lab Partner(s): DeSean Lawrence Ms. Boulougouris 10/31/14 Purpose The purpose of this experiment is to analyze the properties of four different types of solids: ionic, polar covalent, non polar covalent, and metallic Hypothesis It is hypothesized the samples which are shown to be insoluble are likely non polar, while soluble samples are polar. Because of the molecular nature of each type of bond, it is hypothesized that polar covalent molecules It is hypothesized that the samples which are insoluble in water are likely to be non-polar molecules or network covalent and the samples which dissolve are either ionic or polar molecules to have dissolved in the water.…
Enthalpy of dissolution: Trial H2O (g) MgCl2(g) Ti (C) Tf (C) Qsol (J) Qtot (J) ∆H (kJ/mol) 1 20 .5…
There may have been errors in the lab that may have affected the results of the lab. There may have been mistakes: a person may have not measured the substances correctly while retrieving the liquids in the graduated cylinder, or not have been watching the conductivity probe while the group was measuring the electrolyte solution. Along with these, there is also the issue of timing the testing incorrectly. Adding onto this, there may have been a slight spill where the accurate amount of the substance being used was not completely added into the water for testing.…
In our experiment, to look deeper into exothermic reactions, we first had to create our own calorimeter. We did this using 3 separate 8 ounce Styrofoam cups, one for each compound. We then used cardboard to create a lid for each cup and taped it to the sides so the seal would be as tight as we could make it. We also needed a 150mL beaker to measure out the 50 mL of distilled water that we used in each trial to dissolve each compound in. To weigh out each compound we also needed an electronic balance.…
Introduction In this experiment, we mixed different amounts of reactants and measured the volume of O2 they produced so that we could determine the rate and order of the reaction. Three trials were done, the first trial acted as a baseline, then the following two trials each varied the concentration of a single reactant, allowing us to calculate the order of the reaction. Additionally, the temperature of the solution was changed to see what effect that would have on the rate. Using this information the activation energy for this reaction could be calculated and compared to the activation energy of the uncatalyzed reaction.…
The experiment began with a reaction of a 1cm3 cube of lamb liver and 5mL of hydrogen peroxide solution being put in test tubes in a beaker filled with 10℃ water until the temperatures of the liver and hydrogen peroxide were 10℃ also. The liver was put into a 100mL measuring cylinder and the hydrogen peroxide was also poured in as the timer was started. After twenty seconds, several millilitres of froth had been produced from the chemical concoction. This froth was recorded into a results table, and the previous steps were repeated but with increasing temperature increments of 10℃ until 50℃. After carefully completing the experiment, the final results obtained by measuring the volume of the froth produced after 20 seconds, were recorded in a table - see Table 1, and able to be observed in a graph, see Figure 7.…
“Classifying Chemical Reactions - Lab Report” I - Introduction - Chemistry is the study of the composition, structure, properties and change of matter. In chemistry, chemical and physical changes are used to help scientists understand how different substances react given various circumstances. A chemical change is any change resulting in the formation of a new chemical substance(s). A physical property is any change that does not involve the chemical makeup of a substance at all. In total there are five (5) chemical reactions.…
In this lab, we carried out a variety of reactions using different chemicals and metals. A chemical reaction is when the chemical state of the substance you are testing rearranges its ionic and molecular structure. One of the reactions we experienced was single replacement, this consists of one ion switching places with another ion to form a new compound. Another reaction we saw was double replacement. In this reaction, two compounds ions are switched to form two new compounds.…
The purpose of conducting this experiment was to explore how different factors affect the reaction rate of enzymes reacting with their corresponding substrates in order to learn more about how enzymes function in different environments. The independent variables investigated in this experiment were the concentration of different substrates, the temperature of the environment, and the effect of a catalyst on the reaction rate. The dependent variable for all of the investigations was the time it took for the reaction to occur. To investigate the effect of the concentration of the substrate on the reaction time, four test tubes were used.…
Scenario 1 describes the reaction that takes place between H2 and I2 to form the acid HI. This reaction involves very intricate and steps that are critical to understanding the concept of equilibrium as a whole. First, an important concept to understand when describing any reaction is the idea of collision probability. When we examine gas molecules in a 1 cm3 container, there can be billions of collisions per second between neighboring molecules, and even then, maybe only one of these collisions result in a reaction. If any one collision occurs, the only way they will react to form a new molecule, in this case an HI molecule, is if they meet specific activation energy requirements.…
Conclusion: The the precipitation reactions lab eight out of the fourteen occurring reactions were precipitates. A precipitate means that a solid substance was formed or a substance that is not aqueous was formed. The reactions that did not form a precipitate were DNR, which means that they did not react. At station one barium chloride and potassium nitrate did not react but barium chloride and silver nitrate reacted to form barium nitrate and silver chloride. The precipitate at station one was silver chloride.…