Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
124 Cards in this Set
- Front
- Back
Which of the following is not looked for durning a visual preventative maintenance inspection: Fungus growth, Corroded connectors, Sand and grit deposits, or Voltage within tolerances
|
Voltages within Tolerance
|
|
What type of damage softens the protective conformal coating on circuit boards and components?
|
Solvent
|
|
What lubricant is available in an aerosol and used for light to moderate loads?
|
Silicone
|
|
The composite tool kit (CTK) program was developed to?
|
Eliminate damage to aircraft, equipment, and control tool assets
|
|
Which method of tool layout prevents a quick, accurate inventory of a composite tool kit (CTK)?
|
Tools set loosely in drawer
|
|
How are small tools, which cannot be marked, controlled in a composite tool kit (CTK)?
|
In a container marked with the identification number and number of tools contained within
|
|
What helps to dissipate and lessen the effect of electrostatic discharge?
|
humid air
|
|
At what voltage level can electrostatic discharge (ESD) not be seen, felt, or heard?
|
4,000
|
|
What material is designed to prevent the generation of static charge, but is not a static shield?
|
Antistatic
|
|
What precaution must you take before installing an electrostatic discharge (ESD) line replaceable unit (LRU)?
|
Ensure the aircraft is properly grounded
|
|
Shielded cable consists of?
|
A metallic braid over the insulation
|
|
Which type of cable is used to carry radio frequency (RF) power from one point to another?
|
Coaxial
|
|
What type of cable is required for greater shielding against electromagnetic interference?
|
Triaxial
|
|
What advantage of fiber optic cable allows for greatly increased information-carrying within a single fiber?
|
Wider bandwidth
|
|
In a fiber optic cable, what affect does increasing the frequency of a signal have on signal attenuation?
|
none
|
|
What commponent of a fiber optic communication system changes electrical energy in the form of current into optical energy (light)?
|
Source
|
|
What transmitter device changes electrical signals into light signals?
|
Injection Laser diode
|
|
Which receiver device produces current in response to incident light?
|
Pin photodiode
|
|
What is the reflective surface that propagates light along the optical transmission path?
|
Cladding
|
|
When wavelength equals rate of travel/frequency, the wavelength for a sine wave with a frequency of 2MHz is?
|
150 meters
|
|
A transmission line with a simple construction, hight radiation loss, and high noise pickup describes?
|
A parallel two-wire open line
|
|
How do you ensure that a coaxial cable is outputting maximum signal strength?
|
Check the standing-wave-ratio of the cable
|
|
What type of loss occurs as a result of electrical current flowing through a conductor?
|
Copper
|
|
When performing electrical measurements of radio frequency (RF) lines, which of the following will not load the line and upset its normal characteristics?
|
A slotted line section
|
|
The disadvantage of using a waveguide is its?
|
Size restrictions
|
|
The most common device used to connect the section of a waveguide is the?
|
Choke joint
|
|
Which is not a type of coupling device normally found in an electrical connector?
|
Insertion
|
|
The minimum ben radius of a coaxial cable is?
|
Six times the outer diameter
|
|
Which of the following is not proper procedure for soldering a center pin on a coaxial cable center conductor?
|
Apply heat at the dielectric end of the center pin body
|
|
What length of lacing cord is required to properly lace a cable bunch?
|
Two and a half times the length of the finished bundle
|
|
Which condition of an EMP hardened cable is considered non repairable by local personnel?
|
Damage to internal wires
|
|
What percentage of minor shield damage can the flight line technician repair?
|
up to 25 percent of the outer shield circumference
|
|
What precaution must you adhere to prior to applying heat shrink on a wire repair job?
|
Warnings concerning use of heat tools on aircraft
|
|
What type of fiber optic loss occurs when part of the light being transmitted is blocked?
|
Lateral displacement
|
|
What method, uses to produce correct end finishes during a fiber optic cable splice, is more commonly used with connectors?
|
Polish
|
|
What fiber optic connector is best used in rugged, high vibration areas?
|
SMA
|
|
What multiplexing method is used to transmit information over a data bus?
|
Time division
|
|
All the following are advantages of a multiplex bus except: Increase reliability, decrease available space, reduces aircraft weight, reduces the volume of wires
|
Decrease available space
|
|
How is a serial multiplex bus deferent then a parallel multiplex bus?
|
All data bits are received in sequence and uses less twisted wire pairs
|
|
A 1553 data bus message must contain at least one command word with a maximum of how many data words?
|
32
|
|
The typical 1553 data bus system command that provides a mechanism for a remote terminal (RT) to send data to another RT when the BC does not require the data is called?
|
RT to RT
|
|
Which of the following is a function of the MIL-STD-1553 data bus mode codes?
|
Commanding an RT to initiate system self test
|
|
On the B-1B, Which of the following which of the following is not a major aircraft structural area? Fuselage, Windows, Stabilizers, Wing-carry through
|
Wing-carry through
|
|
How many fuselage sections is the B-1B divided into?
|
5
|
|
The forward intermediate fuselage of the B-1B contains?
|
two weapon bays
|
|
The B-2A is divided into how many major sections?
|
Five
|
|
Which B-2 aircraft section serves as the exhaust ramp surface?
|
Aft intermediate
|
|
Which B-2 doors have blade seals?
|
Exterior
|
|
Section 41 of the B-52 fuselage contains the?
|
Upper and lower crew compartments
|
|
Which engine cowling covers starter cartridges and the engine combustion chamber?
|
Afterbody cowl
|
|
What assembly allows the helicopter to move in multiple directions?
|
Main Rotor
|
|
What part of the helicopter counteracts the torque condition?
|
Tail rotor
|
|
What system provides defogging of windows and cabin pressurization?
|
Air-conditioning
|
|
What system consists of emergency exits, ejection seats, and hatch jettisons?
|
Crew escape and safety
|
|
What system monitors temperature changes and over heat conditions in the engine nacelles?
|
Fire protection
|
|
Which communication system consista of airborne and ground command post terminals?
|
Air Force satellite communication (AFSATCOM)
|
|
Which communication system provides encryption and decryption of voice communication?
|
Secure
|
|
What navigation system provides position, altitude, speed, and time information from satellites?
|
Global positioning system (GPS)
|
|
Which navigation system provides the aircraft position, ID, altitude, and personal ID?
|
Identification, Friend or foe (IFF)
|
|
Which system allows the aircrew to land safely at night or in adverse weather conditions?
|
Instrument landing system (ILS)
|
|
Which navigation system aids in aerial refueling operations?
|
rendezvous beacon
|
|
What navigation system contain a gyro-stabalized platform with acceleration censors?
|
Inertial navigation system (INS)
|
|
What aircraft navigation system determines the aircraft height above the terrain?
|
Radar altimeter
|
|
When approaching over heated aircraft wheels, how do you always approach the wheels?
|
From the front or behind the wheel
|
|
Which area is not a primary fire hazard area on the aircraft?
|
Avionics equipment bay
|
|
What components are used to guard against accidental firing of ejection seats?
|
Safety Pins
|
|
On the ACES II ejection seat, what indicates a "hot" seat?
|
protruding red recovery sequencer
|
|
Which action is not a safety precaution for deactivating chaff/flare systems?
|
Loading expendables during routine maintenance
|
|
The number and position of the fire extinguisher is determined by?
|
Applicable aircraft TO and TO 00-25-172
|
|
From an applied signal, input pulses are collected in binary form, then converted into decimal form for digital readout describes the operation of a
|
Frequency counter
|
|
What piece of test equipment is the most accurate instrument for making frequency and time interval measurements?
|
Frequency counter
|
|
Resolution, in reference to a frequency counter, is the?
|
Degree of accuracy of the reading
|
|
In relation to the time domain reflectometer, horizontal deflection on the cathode ray tube equates to?
|
distance
|
|
What does the vertical deflection on the time domain reflectometers cathode-ray tube indicate?
|
Reflected amplitude
|
|
What determines the distance to the discontinuity of a cable?
|
the reflected amplitude between the transmitted and reflected pulses
|
|
Damage to the sampling gate or tunnel diode of a time doamin reflectometer indicates voltages exceeding?
|
5V was applied
|
|
When determining distance from the time domain reflectometer to the discontinuity, count the number of cathode ray tube (CRT) divisions between the?
|
Leading edge of the incident pulse and the leading of the reflected pulse
|
|
A time domain reflectometer display that start in the upper left corner of the screen drops down at mid screen and departs in the lower right screen indicates?
|
A short
|
|
What indicates a relative signal strength of the received radio frequency (RF) signal?
|
Vertical deflection of the trace
|
|
The span of the display, on the spectrum analyzer, is the size of the band of frequencies that are displayed and adjusted with the?
|
FREQUENCY SPAN control
|
|
Before using the spectrum analyzer to make any measurements, calibrate it by using the?
|
CAL OUTPUT signal
|
|
What piece of test equipment is used to measure absolute or relative power?
|
Power Meter
|
|
What control compensates for a slight sensitivity associated with a particular type of power sensor?
|
CAL ADJ.
|
|
What control compensates for mismatch losses over the frequency range of the power sensor?
|
CAL FACTOR%
|
|
A power sensor is practically a?
|
Transducer
|
|
The power sensor is used to establish the active frequency range and power range within the design parameters of the?
|
Power meter
|
|
When calibrating the power sensor, adjust the CAL ADJ control so that the digital readout indicates?
|
1.000 mW
|
|
Before using the power meter, you must first ensure?
|
It is set to the line voltage you are using
|
|
How many operating modes does the pulse generator have?
|
5
|
|
On the pulse generator, selection of NROM mode produces?
|
A continuous pulse output
|
|
What test equipment is used to complete checkout of the receiver operation (antenna, cables, and line replaceable units)?
|
Radar simulator
|
|
The radar simulator group consists of?
|
3 pulse boxes
|
|
What radar simulator group unit operates in the manual mode only?
|
CW box
|
|
What is unit five of the radar simulator group?
|
Battery charger
|
|
What is the maximum number of threat entries that can be entered in the programmable scenario into a elected pulse box?
|
64
|
|
When unit three of a AN/APM-427 radar group is on, the?
|
green light is illuminated
|
|
The pulse box alphanumeric keyboard has?
|
Two single function keys and fourteen dual function keys
|
|
What key on the pulse box enables the user to the top portion of the dual function keys?
|
2nd
|
|
The radio frequency transmission line test set (RFTLTS) is used to diagnose cable faults through voltage standing wave ratio(VSWR)/return loss measurements and?
|
distance to fault measurement
|
|
What key of a radio frequency transmission line test set (RFTLTS) do you use to access the alpha portion of the alphanumeric key?
|
SELECT
|
|
What radio frequency transmission line test set (RFTLTS) test is based on ratio of power out of a unit under test (UUT) to the RFTLTS power fed into the UUT?
|
Insertion loss
|
|
What major internal radio frequency transmission line test set (RFTLTS) operating function digitizes the radio frequency (RF) and video results of test data?
|
Response measurement
|
|
The accessory kit of the radio frequency transmission line test set (RFTLTS) is unit?
|
2
|
|
When radio frequency transmisssion line test set (RFTLTS) is used, you must use the DTF self-alignment, insertion loss self alignment, or
|
VSWR/return loss self-alignment
|
|
What counter measure dispenser tester (CDT) functional check measures the firing pulse amplitude and pulse duration?
|
Fire
|
|
What countermeasure dispenser system (CMDS) uses the countermeasures dispenser tester (CDT) misfires test when selected by the MODE switch?
|
AN/ALE-47
|
|
What switch on the countermeasure dispenser tester (CDT) allows for the retrieval and display of fire test results?
|
DATA
|
|
What position of the DATA switch is selected to display the fire test main PASS/FAIL indication?
|
GO/NO-GO
|
|
Where on the countermeasure dispenser tester (CDT) LCD display field are the plunger pin arrows shown?
|
Left and Right
|
|
What describes in detail how an electronic Warfare Integrated Reprogramming (EWIR) change affects an ELectronic Warfare (EW) system?
|
Reprogramming impact message
|
|
The software that contains algorithms, theat receive, identify, proccess, and do jamming tasks is the?
|
operational flight program
|
|
What notifies units to upload a specific Electronic Warfare (EW) software change?
|
Implementation message
|
|
What is not a part of the Electronic Warfare integrated reprogramming (EWIR) exercise?
|
Evaluation of routine operational change request
|
|
Which of the following is an Air force reprogramming exercise?
|
SERENE BYTE
|
|
As an electronic Warfare technician, what two primary reprogramming exercise will you probably be involved in?
|
SERENE BYTE and PACER WARE
|
|
The common aircraft portable reprogramming equipment (CAPRE) uses what type of computer?
|
Ruggedized laptop
|
|
The common aircraft potable reprogramming equipment (CAPRE) is powered by a(n)?
|
AC adapter and lithium ion battery
|
|
Which software enables the CAPRE to communicate the reprogramming equipment?
|
CAPRE Communication Manager (CCM)
|
|
Which is a DoD-owned network approved for classified data transfer?
|
SIPRNET
|
|
The CAPRE requires visual inspection of components?
|
annually
|
|
Standard data bus interfaces, supported within the programmer loader verifier (PLV) include RS-232C, RS-422, IEEE-488, and?
|
MIL-STD-1553B
|
|
The programmer loader verifier (PLV) automatic functions include?
|
BIT level 1
|
|
The secure telephone unit (STU-III) is able to provide?
|
Secure and non-secure voice and data capabilities
|
|
How many seconds does it take to change from a clear call to a secure call?
|
16
|