Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
84 Cards in this Set
- Front
- Back
001- Before using an electric drill, what is the first thing you should do? |
Make sure the diameter of the hole to be drilled is within the capacity of the drill |
|
001- The purpose of cutting lubricant in most drilling operations is to increase the... |
Drilling speed and the drill bit life |
|
001- Which minimum articles of safety gear must be worn when using a bench grinder? |
Eye and face protection |
|
001- An electric saw blade must be operating at what speed before it contacts the material being cut? |
Full |
|
002- How many pounds psi of clean, dry air is required at the tool end of the air hose to ensure the tool is operating safely and efficiently? |
90 |
|
003- What condition would prevent an operator from applying power to a hoist or other powered lifting device? |
An AF Form 979 is attached to the unit |
|
003- What should be worn anytime there is a potential for injury from overhead objects during a lifting operation? |
Protective helmets |
|
003- What is the most common type of lifting sling used in the muns career field? |
Wire rope |
|
003- The following are all good safety practices to follow when using a lifting sling except |
Inspecting the sling by passing your bare hand over the body of the sling |
|
004- The annunciators displayed on the Fluke 8025-series multimeter are used to distinguish among... |
Ohms, kilohms, and megohms |
|
004- What are two operational modes of the Fluke 8025-series multimeter? |
Range and hold |
|
005- The steering system on the MHU-141/M trailer has a turning radius of how many inches? |
200 |
|
005- When the MHU-141 trailer is loaded or towed with the hinged deck panels open, what must be done? |
The deck panel supports must be properly positioned and locked in place with quick release pins |
|
006- What is the maximum load capacity of the MHU-110/M trailer? |
15000 lbs |
|
006- The parking brake on the MHU-110/M trailer is applied by... |
Pulling either one of two hand levers located on each side of the front of trailer |
|
007- How many openings are on the deck of the MHU-226 trailer? |
Three |
|
007- What type of steering aids the MHU-226 in a tighter steering radius? |
Four wheel double Ackerman |
|
008- After 463L pallets are positioned on a rollerized trailer, what can you use to secure the pallets to the trailer? |
MB-1 chain assemblies/tie down straps |
|
008- What kind of movement supports on base activities to or from the flightline? |
Operational |
|
009- What munitions item is not loaded into transport modules by munitions personnel? |
20 mm |
|
009- What transport module used for decoy munitions has a maximum capacity of 30 magazines? |
ALE-50 |
|
009- How often should the positive locking devices on the doors of munitions transport modules he checked? |
After loading, unloading, and periodically between stops |
|
010- The purpose of the transport beam beneath the lift arm assemblies on the MJ-1 series lift truck is to... |
Provide added support and to relieve hydraulic pressure from the lift arms when carrying loads for long distances |
|
010- What is the lifting capacity of the MJ-1 series lift truck? |
3000 lbs |
|
What is the lifting capacity of the MHU-83 series lift truck? |
7000 lbs |
|
010- When using the MHU-83 series lift truck with fork adapters, you immediately... |
Reduce its lifting capability by 1000 lbs |
|
010- What happens when you release the accelerator pedal on a vehicle driven with a hydrostatic transmission? |
The unit coasts to a stop very quickly |
|
010- What is the primary drawback to using the hydraulic hand pump to build hydraulic pressure on the MHU-83 series lift truck? |
Extremely slow way to build hydraulic pressure |
|
010- How is the yaw positioning from the cradle or boom controls of an MJ-1 lift truck adjusted? |
Manually |
|
011- What category or categories are Air Force air compressors classified? |
High/low pressure |
|
012- The primary difference between a bobtail and a pickup truck is the... |
Bobtail's back end is shortened by about one half |
|
013- What is the purpose behind good operator maintenance of all assigned vehicles? |
Maintain vehicle serviceability at reduced cost |
|
014- What is the maximum amount of pounds the MB-4 aircraft towing tractor can tow and push? |
140000 |
|
015- Pintle safety locking pins must remain attached to the Pintle assembly... |
To prevent an unsecure pin from coming out and getting lost |
|
016- What gear range should be selected in a tractor with an automatic transmission while going downhill? |
Low range |
|
What is the purpose of the trailer hand valve (Johnson Bar)? |
Test the trailer brakes |
|
016- What are hose couplers (glad hands) used for on tractor/trailer combinations? |
To connect the service and emergency brake Airlines from the tractor to the trailer |
|
016- Which procedure is not a consideration for backing a tractor/trailer combination? |
Turn toward the passengers side |
|
017- What is the maximum depth of water you may drive a rough terrain forklift through? |
5ft |
|
017- What is the most beneficial attribute of using the swingmast forklift? |
Allows you to maximize the available storage space |
|
017- With the forks level, what is the maximum reach of the variable reach forklift? |
22ft |
|
018- What USAF gun system is loaded/unloaded by LALS? |
The M61A1, 20mm cannon |
|
018- Which weapons replaceable assembly of the LALS has no moving parts? |
Storage container |
|
019- Which subassembly of the UALS houses a remaining indicator window that provides the means to visually determine the approximate number of rounds in the unit? |
Outer drum |
|
019- Which subassembly of the UALS provides the means to load live rounds into the aircraft gun system? |
Interface unit |
|
019- Which subassembly of the UALS provides the power that cycles the rounds through the system? |
Pneumatic regulator |
|
020- How often should UALS replenisher assemblies be inspected? |
Every 30 days when in use and annually when in storage |
|
020- Which subassembly on the UALS replenisher assembly prevents accidentally loading a spent cartridge into the loader assembly? |
Empty space preclusion device |
|
020- Which tool can initiate cycling ammo through the UALS replenisher manually? |
1/2 inch speed wrench |
|
020- What happens to the unfired rounds returning from the loader when the linked ammo is being processed? |
Automatically downloaded through the second gate in the bottom of the replenisher |
|
021- Which 30mm cannon is internally mounted in the A-10 aircraft? |
GAU-8/A |
|
021- Which 30mm ammo loading system is used to service the GPU-5/A gun pod? |
GFU-10/E |
|
022- Which component of the MAC can be used as a forklift adapter to raise the gantry to full height? |
ICB |
|
022- What is the weight capacity of the pneumatic hoists that are attached to the gantry's I-beam of the MAC? |
4000 lbs (A/E32K-3, MAC), 6000 (A/E32K-9, MAC II) |
|
022- The triple bomb bar is fitted with bomb slings and is used with each hoist to provide for lifting... |
Three 500lb munitions at a time or two 2000lb munitions items |
|
023- Which TO covers the rapid assembly and inspection procedures of nonnuclear munitions? |
11A-1-63 |
|
023- What is the minimum number of feet required to assemble the A/E32K-3, MAC? |
50 x 100 |
|
023- Why is it important to monitor NEW during a bomb buildup operation? |
If ignited, excessive NEW may cause propagation of an explosive from one location to another |
|
023- When packing up the MAC it is important to cap the ends of the air hoses to keep... |
Foreign materials from damaging them |
|
024- What does Title 49 of the code of federal regulations regulate? |
Shipments of hazardous material, including explosives within the US |
|
024- Which approved restraining devices can be used for securing muns on USAF vehicles/trailers? |
Chains/binders, cargo nets, and tie down straps |
|
024- When is it permissible to transport explosives in POVs? |
Never |
|
024- What is the primary focus when designating primary and alternate explosives movement routes? |
Use the safest possible routes |
|
025- What source is best used to determine the explosive hazard class/division of a specific munitions item? |
JHCS |
|
026- What should you do if a conflict is discovered while using TO 11-1-38 between the illustrations and the written procedures? |
Follow the written procedures |
|
026- Even though TO 11-1-38 has its own safety section, what other publication should you reference for safely transporting explosive items on base? |
AFMAN 91-201 |
|
026- what type of info is given in the general notes on the first card of each trailer and weapon type section in TO 11-1-38 and is required to be reviewed? |
WARNINGS, CAUTIONS, & NOTES pertaining to each trailer and weapon |
|
026- If you cannot fully close the load binder handle by hand, |
Adjust the load binder hooks on the chain |
|
026- What chapter of TO 11-1-38 covers configuration of the MHU-141 munitions trailer? |
One |
|
026- What piece of equipment must be used with the MHU-110 to prevent the trailer from becoming unstable while using the rail extenders for loading/unloading heavy munitions? |
Stabilizer jack |
|
026- What can be constructed and attached to the bed of a 40-ft trailer to facilitate support of rounded munitions? |
Wooden rail sets |
|
027- What provides an itemized list of all equipment authorized for use with nuclear weapons? |
Master nuclear certification list |
|
027- Once verified that an item is nuclear certified, how is it identified as such? |
Positive identification by nameplate, label, appropriate markings, or by official documents |
|
027- Which statement about pintle hooks and their use in operations with nuclear weapons is correct? |
Original equipment pintle hook assemblies are authorized |
|
027- Which items do not require nuclear safety certification for use in operations with nuclear weapons? |
General purpose hand tools |
|
028- When should you replace a nuclear certified MB-1 tie down/chain assembly item? |
After finding any cracks, bent/worn parts, or excessive corrosion |
|
028- Which action is not an authorized method for securing loose lengths of chain when using the MB-1 tie down device/chain assembly? |
Wrap the loose ends around the tie down device and secure to the quick release lever |
|
028- When using a load binder for securing a load what's the main reason for not using a cheater bar or extension tool to fully close the handle? |
It would place too much pressure on the load/tie down points |
|
028- When specifically authorized for transporting nuclear weapons and material, how many CGU-1/B tie down straps need to be used as a substitute for every one MB-1 tie down assembly? |
2 |
|
029- What are the key factors to consider during a nuclear weapons movement? |
Safety and security |
|
029- Which area is designated as a location used temporarily during a delay of an off base movement involving nuclear weapons? |
National defense |
|
029- What code word is used when DOE convoy seeks sanctuary during an emergency? |
Safe Haven |
|
029- When are nuclear weapons moved by convoy? |
Every time weapons are moved |
|
029- What is the most difficult job for escort guards during a convoy? |
Keeping other vehicles from entering the convoy |