Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
52 Cards in this Set
- Front
- Back
DC loadmeter limit |
0-1.03 |
|
AC voltmeter limit |
110-125 |
|
DC voltmeter limit |
25-30 |
|
AC frequency limitation |
380-420 Hz |
|
AC bus off light illuminates at |
90 volts |
|
The minimum voltage for battery bus is... |
21 volts |
|
The generator light illuminates at... |
70 volts |
|
The max load of the ATM generator with the cooling fan inoperative or 104*F is |
.66 or 66% |
|
The AC instruments and fuel control inverter (in ESS DC position) uses... |
115 volts/400Hz in phase A |
|
The max load of an AC engine generator is... |
.72 or 72% |
|
The rated load of the ATM with cooling fan operative is... |
1.00 |
|
The suction boost pump pressure is... |
70-90 psi |
|
The auxiliary accumulator pre-charge pressure is... |
300 +/- 100 psi |
|
The utility accumulator pre-charge pressure is... |
1500 +/- 100 psi |
|
The auxiliary system pressure is... |
2900-3300 psi |
|
The booster system pressure is... |
2900-3200 psi |
|
The emergency brake accumulator pressure is... |
1000 +/- 100 psi |
|
The suction boost pump warning light will illuminate at... |
20 psi |
|
Full hydraulic system pressure will be reached within... |
30 sec after on speed |
|
The maximum system pressure for utility is... |
3500 psi |
|
The engine pump warning light will come on if the pressure drops to about... |
1000 psi |
|
The wing overheat temperature is... |
200-up°F |
|
Wing isolation valves are ______ closed/________ opened |
Electrically/Manually |
|
Minimum pressure for bleed down is... |
35psi |
|
Normal wing temperature operational range is... |
75°-200° F |
|
Inoperative wing temperature range is... |
75° or below |
|
Maximum running time for wing anti-icing is... |
30 sec |
|
GTC oil pressure switch setting is... |
3 psi |
|
GTC overspeed switch is... |
110% rpm |
|
Start light goes "out" at... |
35% rpm |
|
On speed light comes "on" at... |
95% rpm |
|
GTC starter duty cycle is... |
1 on, 4 off |
|
Bleed down check limit is... |
30 to 15 psi in no less than 8.5 sec |
|
Fire bottle pressure is... |
600-640 psi |
|
Agent discharge switch should not be held more than... |
2 sec on |
|
Turbine overheat is indicated by a... |
Flashing light in the T handle |
|
There are __ turbine overheat detectors, set at... |
4, 700°F |
|
Engine fire is indicated by a... |
Steady light in the T handle |
|
Do not hold the turbine overheat test switch more than... |
30 sec on |
|
There are __ nacelle overheat detectors, set at... |
6, 300°F |
|
Fire detection system uses... |
Inconel tubing |
|
The torquemeter shaft measures... |
Engine output |
|
Normal limiting mode is... |
Less than 66° throttle and at 94% rpm |
|
Safety coupling setting is... |
-6000 in/lbs torque |
|
The combustion section is... |
Can-annular |
|
The turbine section has... |
4 stages |
|
The compressor section is a... |
14 stage axial flow |
|
Compressor discharge pressure/temp is... |
125psi/600°F |
|
Temperature controlling mode is... |
Greater than 66% throttle and at 94% rpm |
|
Start limiting mode is... |
94% rpm |
|
Maximum allowable torque is... |
19600 |
|
Crossover is at... |
66° throttle |