Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
162 Cards in this Set
- Front
- Back
|
What is fastener control?
|
Accounting for all fastners pre and post flight.
|
|
|
How much settling time is required after an a/c has ben moved or refuled before taking a fuel sample?
|
2 hours
|
|
|
What position should the anti-skid switch be in ashore? afloat?
|
Ashore: ON
Afloat: OFF |
|
|
How often do we pre-op equipment?
|
Before every use.
|
|
|
How many fasteners can be missing forward of the intake?
|
None.
|
|
|
Demonstrate hand signals for INS, IFR extend, IFR retract tail hook up, tail hook down, open speed brake, close speed brake, launch bar up, launch bar down and beer can in and beer can out.
|
(Have trainee demonstrate)
|
|
|
What does AMAD stand for?
|
Airframe Mounted Accessory Drive.
|
|
|
Can we taxi a/c with only one engine online?
|
Yes only if it's engine 2 because engine 2 controls break pressure and NWS.
|
|
|
What's the difference between 3 down on the beach and 3 down on the boat?
|
Beach: tail hook, IFR probe, Speed brake
Boat: launch bar, IFR probe, Speed brake |
|
|
What's the time required to charge the battery of an a/c?
|
30 Minutes
|
|
|
What is the nomenclature for hydraulic fluid used?
|
MIL-PRF-83282 or MIL-H-5606 (alternate)
|
|
|
How many turns is required to open a canopy of an A,C and B,D externally?
|
A,C: 35+/-1
B,D: 112+/-1 |
|
|
How many fasteners are in door 3?
|
52
|
|
|
What is the MMP code 916?
|
arresting gear damper pressure low
|
|
|
What is the MMP code 904?
|
Hard landing inspection?
|
|
|
What is the MMP code 871?
|
right generator fail
|
|
|
What is the MMP code 903?
|
Hard landing data
|
|
|
What is the MMP code 819?
|
Right ATCV open
|
|
|
What is the MMP code 825?
|
cabin air flow incorrect?
|
|
|
What is the MMP code 834?
|
left pitot heat circuit fail
|
|
|
What is the MMP code 835?
|
right pitot heat circuit fail
|
|
|
What is the MMP code 870?
|
Left generator fail
|
|
|
What is the MMP code 817?
|
Right AMAD oil pressure low
|
|
|
What is the MMP code 818?
|
Left ATCV open
|
|
|
What is the MMP code 982?
|
Left AMAD oil level low?
|
|
|
What is the MMP code 983?
|
Right AMAD oil level low.
|
|
|
What is the MMP code 984?
|
APU oil low
|
|
|
What is the MMP code 988?
|
fire extinguisher low
|
|
|
What is the MMP code 995?
|
Fluids test complete
|
|
|
What is the MMP code 996?
|
LOX Low
|
|
|
What is the MMP code 997?
|
Hyd. system 1 level low
|
|
|
What is the MMP code 998?
|
Hyd. system 2 level low
|
|
|
What is the MMP code 980?
|
left engine oil level low
|
|
|
What is the MMP code 981?
|
right engine oil level low
|
|
|
What is the MMP code 811?
|
overstress
|
|
|
What is the MMP code 812?
|
memory unit low storage space
|
|
|
What is the MMP code 816?
|
left AMAD oil pressure low
|
|
|
What is the MMP code 809?
|
Memory unit full
|
|
|
What do you do if an a/c vents fuel in skids? Hot skids?
|
FUEL SKIDS: stop fueling, notify maint. if over 5 gal. (maint. will call fire dept.), clean up spill
HOT SKIDS: stop all fueling, if there is another a/c move that a/c first then shut down a/c venting fuel, notify maint., clean spill |
|
|
What is a conditional inspection and what pup can they be found in?
|
Performed when unscheduled maint. events occur (ie. hard landing, acceptance/transfer, bird strike, lightening strike)
FA-18AC-LMM-030 |
|
|
What is the purpose of a DTA?
|
to ensure a/c is safe for flight and to notify maint. of any damages to a/c
|
|
|
what are the tie down requirements during heavy weather conditions ashore? afloat?
|
ASHORE: 12
AFLOAT: 24+ |
|
|
What is the purpose of diving your ducts?
|
to ensure that the engine has not been fodded out and that there is no damage to any of the components of the inlet
|
|
|
How many delta-p's must be checked on the a/c? Where are they?
|
18 (there are 19 total)
1 above dragbrace, 3 in each main (Case drain, pressure relief filter, return filter), 1 in door 54L/R, 2 in door 65L/R (engine and VEN), 2 in door 69R/L (Fuel filter), 1 in door 52 (APU), 1 in door 52 above APU that cannot be seen (19th) |
|
|
behind what door is the LOX bottle located?
|
13L
|
|
|
What is the proper tail hook pressure?
|
300-400 psi
|
|
|
How many fastners can be missing on a fuel cell panel?
|
none
|
|
|
What does MSDS stand for and where is it located?
|
Material Safety Data Sheet
Hazmat |
|
|
Demonstrate the hand signal for a fuel leak.
|
(trainee demonstrates)
|
|
|
How do you set up a cockpit for flight?
|
-All switches in NOASS, except anti-skid, parking brake on, flaps OPEN, tail hook up, wing fold matches wing position, check seat pins, clean displays and canopy, neatly position and extend all straps, check LOX load and memory unit and fuel load
|
|
|
What is a special inspection and what pub can they be found in?
|
Performed when an a/c has reached a specific limit in flight hours, elapsed calendar days, etc.
FA-18AC-MRC-250 |
|
|
When do you inventory your tools?
|
Once you check them out, before you leave the work center, once you get to your work station, while you're doing a task, after you finish a task, before you leave your workstation, once you get back to the workcenter and before you turn them back in
|
|
|
What is the purpose of a hot seat?
|
to save turnaround time
|
|
|
when is a fuel sample required?
|
before the first flight of the day, and during a daily inspection
|
|
|
How much does JP-4 weigh? JP-5?
|
JP-4: 6.5 lbs/gal
JP-5: 6.8 lbs/gal |
|
|
what is a hot start?
|
When there is not enough fuel during startup in the engine
|
|
|
how long is a daily inspection good for?
|
72 hours unless flight or major maint.
|
|
|
why is tool control so important?
|
to reduce FOD hazards and costs
|
|
|
what are you saying when you sign the "A" sheet?
|
All tools are ATAF, every gripe has a MAF initiated, and that you've inspected the a/c in accordance with the MRC-200
|
|
|
Who is responsible for FOD?
|
All hands
|
|
|
What are the tie down requirements during moderate weather conditions? Ashore? Afoat?
|
ASHORE: 6
AFLOAT: 12 |
|
|
How many tie downs are required during normal weather conditions ashore? Afloat?
|
ASHORE: 3
AFLOAT: 6 |
|
|
how long is a turnaround inspection good for?
|
24 hours unless flight or major maint.
|
|
|
Who signs the "A" sheet?
|
PC, pilot, ordie, safe for flight maint. controlman
|
|
|
How many volts of static discharge are possible on a canopy after flight?
|
100,000 volts
|
|
|
How do you know that a MAF has been completely signed off?
|
4 signatures; worker, CDI, supervisor, and SFF maint.
|
|
|
What are the procedures to take when you get a bad fuel samples?
|
drain one gallon, drain one more pint, if still bad take both samples to QA
|
|
|
Why do we shut down one engine during recoveries?
|
to ensure controls work properly with one engine online (AKA switching valve check)
|
|
|
what items are required for a daily inspection?
|
MRC-200, tool pouch, cranial, TPG, FSK, lint-free cloth w/ hyd. fluid, mirror
|
|
|
What is the max PSI while fueling?
|
55 psi
|
|
|
How long are fuel samples good for?
|
24 hours
|
|
|
What is the number one priority of a PC?
|
Safety
|
|
|
How many fuel drain points are there on an F/A-18 w/o drops?
|
7 total; 5 along centerline, 1 on each wing
|
|
|
approx. how much fuel do you drain from each wing tank?
|
1 pint
|
|
|
what are you inspecting each container of fuel for?
|
water, foreign objects, microbiological organisms
|
|
|
When does the VEN system require servicing?
|
when the RAM is at the midpoint of the slot or lower.
|
|
|
How many turnarounds are kept in the ADB? What do they represent?
|
10; they represent the last ten flights
|
|
|
What do you write on the daily card if the a/c is tail over water?
|
TOW
|
|
|
What is the minimum number of times you can cycle the wings ebfore a cool down period is required?
|
two times
|
|
|
Where can the actual weight of the a/c be found in the ADB?
|
Weight and Balance sheet.
|
|
|
how much cool down time is required before cycling the wing fold after two cycles?
|
12 minutes.
|
|
|
What is the acronym MMP?
|
Maint. monitor panel.
|
|
|
What two fluids to we monitor in the ADB?
|
Hyds and engine oils
|
|
|
why would you need the actual weight from the weight and balance sheet?
|
MLG strut servicing
|
|
|
How many delta-p's do you check on a turnaround?
|
6
|
|
|
What do you do if there are any uncertainties during a launch?
|
Suspend launch and get a troubleshooter
|
|
|
What is the max weight and grade that you can tow an a/c?
|
49,387 on a 3% grade
|
|
|
How many delta-ps do you check on a daily?
|
12
|
|
|
what military specification number do we use for servicing engines?
|
MIL-PRF-23699 or MIL-L-7808
|
|
|
How many seconds are allowed for a pre-check when fueling?
|
45
|
|
|
What is being tested during a Pro-A?
|
Everything and electrical power?
|
|
|
What is being tested during a Pro-B?
|
Engines
|
|
|
What is being tested during a Pro-C?
|
Flight controls
|
|
|
How long after shutdown do you have to service engine oil before an engine turn is required?
|
1 hour
|
|
|
what does it mean when the oil indicator is bright silver after servicing?
|
oil tank internal overfill tube is defective.
|
|
|
What is the max psi when fueling a jet with new foam in the wings?
|
25 psi
|
|
|
What is the minimum pressure required for a pre-check?
|
20 psi
|
|
|
What does it mean whtn the oil level indicator appears dark?
|
oil level is correct
|
|
|
How long after shut down do you have to service the AMAD oil system?
|
30 minutes
|
|
|
Are you allowed to mix MIL-PRF-23699 and MIL-L-7808
|
Yes, but the system must be drained and serviced with one type ASAP
|
|
|
what is the flash point for JP-4? JP-5?
|
JP-4: 0 degrees F
JP-5: 140 degrees F |
|
|
Which side of the ADB are outstanding gripes located? Signoffs?
|
OUTSTANDING: Right
SIGNOFF: Left |
|
|
What programs does the 4790.2A chapter 10 cover?
|
Plane Captin program, fuel surveillance, Fod Prevention, Tool control program, Corrosion prevention and control, tire and wheel maint. safety, egress/explosive system check out, SE operation training and licensing, Hazmat control and management
|
|
|
What is the a/c tires and tubes manual?
|
NAVAIR 04-10-506
|
|
|
What pub is the aircraft refueling NATOPS manual?
|
NAVAIR 00-80T-109
|
|
|
When and why should you review the ADB?
|
Before a daily and pre-flight einspection to ensure the previous gripes have been corrected and to look for reoccuring gripes during daily inspections
|
|
|
What pub is the aviation hydraulics manual?
|
NAVAIR 01-1A-17
|
|
|
How many grounding points are on the a/c and where are they located?
|
7; 1 in NWW, 1 in door 8 (fuel door), 2 in each main, 1 in door 164 (fwd of tailhook).
|
|
|
What pub covers corrosion control and prevention?
|
NAVAIR 01-1a-509
|
|
|
How many wet stations are on an a/c and which ones are they?
|
3 stations; 3, 5, 7
|
|
|
What is the NATO code for JP-5?
|
F-44
|
|
|
What pub covers a/c fuel cells and tanks?
|
NAVAIR 01-1a-35
|
|
|
what pub contains scheduled/conditional maint./ phase maint.?
|
A1-F18AC-MRC-300
|
|
|
What pub covers conditional inspections?
|
A1-F18-AC-LMM-030
|
|
|
what are the safety precautions for launching an a/c w/ ordnance?
|
ensure all ord. is safe and secured w/ pins; never stand directly in front of foward firing ordnance and never walk under any ordnance
|
|
|
what is the width of the a/c w/ wings folded?
|
27ft 5in
|
|
|
What pub covers SE common basic handling and safety?
|
NAVAIR 00-80T-96
|
|
|
What is the length of the a/c?
|
56ft
|
|
|
How many spray bars are in the exhaust all together?
|
24
|
|
|
How many pounds can a tie down hold?
|
10,000 lbs
|
|
|
What pub contains SE cleaning, preservation, and corrosion control?
|
NAVAIR 17-1-125
|
|
|
What does ADSU stand for?
|
Airstream directional sensing unit
|
|
|
what pub covers a/c restraining manuals?
|
NAVAIR 17-1-537
|
|
|
What pub is the a/c refueling handbook?
|
NAVAIR 00-80R-14
|
|
|
What pub covers scheduled maint/conditional maint/ special maint.?
|
A1-F18AC-MRC-250
|
|
|
Where can you find the pon-6 pre-op?
|
NA-19-600-58-6-1
|
|
|
Where can you find the HSU pre-op?
|
AG-140BA-MRC-100
|
|
|
What does ATSCV stand for?
|
Air turbine starter control valve
|
|
|
Can you service the hyds. during 4 down?
|
No, b/c you will not get an accurate reading and it is easy to overservice
|
|
|
How many IGVs do you inspect in each intake?
|
18
|
|
|
What does RLCS stand for?
|
Radar liquid cooling system
|
|
|
What does Delta-P mean?
|
differential pressure
|
|
|
How many tie down pts are on the a/c and where are they located?
|
12pts. 2 in NLG, 1 in door 16R (behind dragbrace faring), 3 on each main, 1 in door 107L/R (wings), 1 in door 164 (fwd of tailhook)
|
|
|
What do you do if the APU will not spool down?
|
flip the emergency shut-off switch in the NWW. if that doesn't work, pull CB#8 in door 10L
|
|
|
How do you determine the NLG X-demensions?
|
based on the ambient temp. and plaque located on NLG.
|
|
|
What is a wet start?
|
When the engine is flooded w/ fuel during startup
|
|
|
how many people are required to move an a/c with brakes? Without brakes?
|
BRAKES: 6
NO BRAKES: 7 |
|
|
What pub contains line emergency procedures?
|
A1-F18AC-LMM-020
|
|
|
What does the A1-F18-MRC-100 and A1-F18-MRC-200 cover?
|
MRC-100: Turnaround inspection
MRC-200: Daily inspection |
|
|
What pub contains a/c hand/wand signals?
|
NAVAIR 00-80T-113
|
|
|
Where can you find basic information on a/c?
|
A1-F18AC-GAI-000
|
|
|
What pub is the fault reporting manual?
|
A1-F18AC-FRM-000
|
|
|
What is the CV NATOPS manual?
|
NAVAIR 00-80t-105
|
|
|
What is a hung start?
|
When the engine does not come online and shuts down when cranking stops
|
|
|
How many 1st stage blades do you inspect in each intake?
|
32
|
|
|
What is the width of the a/c wing tip to wing tip?
|
MISSLES: 40ft 4in
LAUNCHERS: 38ft 4in WITHOUT LAUNCHERS: 37ft 4in |
|
|
What is the OPNAV form number for the A-sheet? Daily Card?
|
A-SHEET: 4790/141
DAILY: 4790/38 |
|
|
Why do we mark the launch card for hyds. before and after start?
|
to detect air in the system. HS1 can only move one increment and HS2 can only move 3 increments before it is a downing descrepancy
|
|
|
Why do we mark the launch card for hyds after shutdown?
|
To detect fluid migration
|
|
|
What is the max wind speed allowed for opening the canopy?
|
60 knots
|
|
|
How far away should personnel and equipment be clear of overheated wheels/tires and blown tires?
|
Minimum of 300ft
|
|
|
What is the indication of an a/c w/ no brakes?
|
Speed brake is up and the tail hook is down
|
|
|
What is the indication of an a/c without NWS?
|
Taxi light on or flashing
|
|
|
How many turns are required to manually open the canopy internally on an A,C and a B, D?
|
A,C: 70+/- 1
B,D: 224+/-2 |
|
|
What is the minimum safe distance to stand from the intake at idle? Military? Max?
|
IDLE: 9ft
MILITARY: 25ft MAX: 25ft |
|
|
what do you do if the psi indicator turns red during fueling?
|
stop fueling immediately
|
|
|
what are the tire pressures for an a/c on the boat?
|
NOSE: 375+/-5
MAINS: 350+/- 5 |
|
|
what are the tire pressures for an a/c ashore?
|
NOSE: 150+/-5
MAINS: 250+/-5 |
|
|
What is the fuel load for an a/c that is to receive a "bounce load" on shore? on the boat?
|
ASHORE: 8.0
AFLOAT: 10.0 |
|
|
Do you need to have the battery switch on to charge the battery of an a/c?
|
Negative, Ghost Rider!
|
|
|
What should you do if the VEN power unit level indicator RAM starts to retract while servicing the VEN?
|
stop servicing, rotate transmisson shaft 180 degrees and continue servicing
|
|
|
where is the safe area to cross under a/c?
|
fwd of the attach point of the tailhook.
|
