Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
141 Cards in this Set
- Front
- Back
- 3rd side (hint)
1. What company makes the conventional lighting console used in the FS Live Main Hall?
|
B. ETC
|
a. Martin
b. ETC c. MA Lighting d. High End Systems |
|
2. Which of these is NOT a type of lamp?
|
D. VMFL
|
a. MFL
b. WFL c. VNSP d. VMFL |
|
3. When using the following fixtures from the same throw distance, which of these fixtures will give you the largest beam diameter?
|
C. Source 4 36 degrees
|
a. Source 4 19 degrees
b. Source 4 26 degrees c. Source 4 36 degrees d. Source 4 10 degrees |
|
4. Which one of these fixture would you use to project a gobo pattern?
|
C. Source 4 19 degrees
|
a. Par 1K VNSP
b. 8” Fresnel c. Source 4 19 degrees d. Par 500W MFL |
|
5. Socapex connector has ____ pins.
|
D. 19
|
a. 6
b. 12 c. 18 d. 19 |
|
6. How many circuits does a standard socapex cable carry?
|
A. 6
|
a. 6
b. 12 c. 18 d. 19 |
|
7. What type of cable do we connect to the end of a socapex so that we may plug fixtures into the individual circuits?
|
B. Break Out
|
a. Break in
b. Break out c. DMX d. 5 pin XLR |
|
8. Where does a conventional lighting fixture get power from?
|
C. Dimmer
|
a. MVL Distro
b. Wall outlet c. Dimmer d. Console |
|
9. DMX stands for _______________.
|
A. Digital Multi-Plex
|
a. Digital Multi-Plex
b. Digital Moving light Power c. Dimmable Master Par d. Digital Mixing |
|
10. How many channels make up one universe of DMX?
|
C. 512
|
a. 255
b. 256 c. 512 d. 8 |
|
11. How many steps exist in one channel of DMX?
|
C. 256
|
a. 8
b. 255 c. 256 d. 512 |
|
12. What type of wiring system do we use to get DMX from the console to all of the fixtures?
|
D. Daisy Chain
|
a. Socapex
b. Star chain c. Break out d. Daisy chain |
|
13. The DMX standard calls for a ____ pin XLR connector.
|
A. 5
|
a. 5
b. 3 c. 7 d. 19 |
|
14. At the end of a DMX data line, a ___________ is used to limit DMX reflections.
|
a. Terminator
|
a. Terminator
b. Opto-Splitter c. Y-cable d. Transformer |
|
15. A piece of gear that is used to limit reflections in a dmx chain has a ____ ohm resistor wired between pins 2 and 3.
|
C. 120
|
a. 1.2K
b. 24 c. 120 d. 20 |
|
16. As per the rules of DMX, no more than ____ devices may be run on one un-split line.
|
B. 32
|
a. 8
b. 32 c. 256 d. 512 |
|
17. If you need to run more fixtures than the maximum allowed on one un-split line, you may use a ___________.
|
B. Opto-splitter
|
a. Terminator
b. Opto-splitter c. Y-cable d. Transformer |
|
18. What was the first fixture introduced by High End Systems?
|
A. Intellabeam
|
a. Intellabeam
b. Trackspot c. Cyklops d. Cyberlight |
|
19. Chas Herrington was the lighting designer that used the High End Systems Intellabeam fixture on what band’s “On Every Street” tour?
|
C. Dire Straits
|
a. Grand Funk Railroad
b. Genesis c. Dire Straits d. Cameleon |
|
20. In 1965, this designer developed a remote controlled par type fixture for a production of “Peter Pan”.
|
B. Jules Fischer
|
a. Peter Wynne Wilson
b. Jules Fischer c. Herber F. King d. Edmund Sohlberg |
|
21. In what city did the 1981 Genesis “Abacab” tour start?
|
A. Barcelona
|
a. Barcelona
b. London c. New York d. Paris |
|
22. What color is the ground connector in the U.S.?
|
A. Green
|
a. Green
b. White c. Black d. Red |
|
23. We commonly use 3 Phase power to supply our lighting systems. How many hot legs exist in a 3 phase system?
|
C. 3
|
a. 1
b. 2 c. 3 d. 5 |
|
24. What color is the neutral connector in the U.S.?
|
B. White
|
a. Green
b. White c. Black d. Red |
|
25. In a 3 Phase System (in the U.S.), how many volts should your meter read between Green connector and the Black connector?
|
A. 120
|
a. 120
b. 0 c. 208 d. 240 |
|
26. In a 3 Phase system (in the U.S.), how many volts should your meter read between the Red connector and the Blue connector?
|
C. 208
|
a. 120
b. 0 c. 208 d. 240 |
|
27. If you have a main disconnect box labeled “3 Phase 200A 120V”, how many total amps can be supplied by this dixconnect?
|
A. 600
|
a. 600
b. 200 c. 120 d. 3 |
|
28. This type of cable is bare copper wire at one end, and has a connector on the other, and is used to “tie in” to the main dosconnect.
|
B. Feeder Tails
|
a. Socapex
b. Feeder Tails c. 10 gauge d. Break Out |
|
29. A common wire size that is used to carry power from the main disconnect to your lighting system is _______.
|
D. 00 Gauge
|
a. 18 gauge
b. 10 gauge c. 4 gauge d. 00 gauge |
|
30. How many pars are on a standard par bar?
|
B. 6
|
a. 4
b. 6 c. 12 d. 18 |
|
31. In Full Sail Live Main Hall, Motor #1 is ____________.
|
C. Downstage Left
|
a. Downstage Right
b. Upstage Right c. Downstage Left d. Upstage Left |
|
32. In Full Sail Live Main Hall, Motor #6 is ____________.
|
B. Upstage Right
|
a. Downstage Right
b. Upstage Right c. Downstage Left d. Upstage Left |
|
33. When connecting a 3 phase power system, what color connector do you plug in first?
|
A. Green
|
a. Green
b. White c. Black d. Red |
|
34. Who normally “ties in” the power to the main disconnect?
|
C. House Electrician
|
a. Dimmer tech
b. Lighting Designer c. House Electrician d. Moving Light tech |
|
35. “The set of wires (hot, neutral, and ground in a three-wire system) that carries power from the last overcurrent protection device to one or more loads” is the definition of what?
|
D. Branch Circuit
|
a. Feeder cable
b. Socapex c. Fan in d. Branch circuit |
|
36. What does “ACN” stand for?
|
B. Architecture for Control Networks
|
a. Active Control Net
b. Architecture for Control Networks c. Align Combination Nodes d. Archived Computer Network |
|
37. What is the maximum current interrupt rating for a breaker that is used in conjunction with 10 AWG circuits?
|
D. 30 Amps
|
a. 10 Amps
b. 20 Amps c. 15 Amps d. 30 Amps |
|
38. “To take control signal input translate it to computer code, and execute commands in the form of motor movements or, in the case of electronic dimming, lamp voltage” is the primary function of what system in an automated luminaire?
|
C. Electronics
|
a. Electromechanical
b. Mechanical c. Electronics d. Optical |
|
46. What company makes the dimmer racks that we use in Full Sail Live 1?
|
C. Leprecon
|
a. ETC
b. Avolites c. Leprecon d. Martin |
|
47. On the automated lighting power distro that we use in Full Sail Live 1, how many pins in each socapex output are hot?
|
C. 12
|
a. 6
b. 9 c. 12 d. 18 |
|
48. What is a benefit of moving head style fixture (as compared to a moving mirror)?
|
D. Greater Range of Motion
|
a. Faster movement
b. More colors c. Weighs less d. Greater range of motion |
|
49. What is a benefit of a moving mirror style fixture (as compared to a moving head)?
|
A. Faster Movement
|
a. Faster movement
b. Takes less power to run c. More gobos d. Brighter lamp |
|
50. Which of these does not use mechanical dimming?
|
B. VL-500D
|
a. Technobeam
b. VL-500D c. Mac 2K Profile d. Mac 600NT |
|
51. Which of these is a moving mirror fixture?
|
B. Technobeam
|
a. VL-500
b. Technobeam c. Mac 500 d. Mac 2000 Profile |
|
52. This can cause a thermal circuit breaker to trip sooner than it should.
|
C. High Ambient Temperature
|
a. Arc lamp
b. Data capacitance c. High ambient temperature d. Bad feeder cable |
|
53. Most moving lights use this type of lamp.
|
C. Arc
|
a. Incandescent
b. Fluorescent c. Arc d. LED |
|
54. What type of filter do most moving lights use to change color?
|
B. Dichroic
|
a. Gel
b. Dichroic c. Douser d. Primary |
|
55. The types of color filters used by most moving lights, change the color of light by …
|
C. Reflecting the unwanted frequencies of the light.
|
a. Absorbing the wavelengths not used
b. Changing the base frequency of the wavelength with power correction. c. Reflecting the unwanted frequencies of the light. d. Altering the lamp voltage |
|
56. Which of these is a primary color of light?
|
A. Red
|
A. Red
B. Yellow C. Magenta D. Cyan |
|
57. Which of these is a secondary color of light?
|
C. Yellow
|
A. Blue
B. Green C. Yellow D. Red |
|
58. The compliment of the color blue is _______?
|
A. Yellow
|
a. Yellow
b. Cyan c. Red d. Magenta |
|
59. The compliment of the color green is _______?
|
A. Magenta
|
a. Magenta
b. Red c. Blue d. Cyan |
|
60. What is the value of the above dip swithces? (The Black square is the actual switch)?
|
C. 26
|
a. 3
b. 21 c. 26 d. 256 |
|
61. If a Mac 500’s dimmer is at full (100%), what dmx value does the dimmer channel have?
|
C. 255
|
a. 0
b. 128 c. 255 d. 512 |
|
62. If you have 5 Mac 600NT’s patched in your console starting at DMX address #1, and each fixture uses 15 dmx channels, what is your next available dmx start address?
|
C. 76
|
a. 6
b. 75 c. 76 d. 16 |
|
63. How many Mac 600NT’s can you individually control on one un-split line of DMX? (each fixture uses 15 channels of DMX).
|
C. 32
|
a. 34
b. 35 c. 32 d. 36 |
|
64. What style of Grand MA console do we use in the programming lab?
|
D. Grand MA Ultra-Light
|
a. Grand MA Micro
b. Grand MA Light c. Grand MA Full Size d. Grand MA Ultra-Light |
|
65. What visualizer program do we use in programming lab?
|
D. ESP Vision
|
a. Wysiwyg
b. MA3D c. Martin Show Designer d. ESP Vision |
|
66. How many DMX universe outputs does the Grand MA Ultra-Light have?
|
B. 2
|
a. 1
b. 2 c. 3 d. 4 |
|
67. How many DMX universe outputs does the Grand MA Full Size have?
|
D. 4
|
a. 1
b. 2 c. 3 d. 4 |
|
68. How many executer faders are found on the Grand MA Ultra-Light?
|
A. 10
|
a. 10
b. 8 c. 16 d. 20 |
|
69. When you power up a Grand MA console, what show loads into the console?
|
C. The last show that was loaded.
|
a. The “blank” show
b. The first show on the hard drive c. The last show that was loaded d. Your show |
|
70. How do you create a new show on the Grand MA console?
|
B. Load a show with a new name.
|
a. Load the “blank” show
b. Load a show with a new name c. Load the “empty” show d. Press the “create new show” button |
|
71. When you want to save your show, the first button you need to press is the ______ button.
|
A. Backup
|
a. Backup
b. Setup c. Tools d. Utilities |
|
72. On the Grand MA, you can save your show to hard drive, file server, USB drive, or ___________.
|
C. Floppy Drive
|
a. DVD drive
b. Zip drive c. Floppy drive d. CD-RW |
|
73. To begin patching your show, you must first press the ______ button.
|
A. Setup
|
a. Setup
b. Backup c. Tools d. Patch |
|
74. When patching fixtures into your show, each fixture gets assigned a letter and a number (ex. B121). What does the letter stand for?
|
A. The DMX Universe
|
a. The dmx universe
b. The name of the fixture c. The style of the fixture d. The type of fixture |
|
75. On the Grand MA Console, Automated Lights are given a fixture ID number, while Dimmers are given a ___________ ID number.
|
B. Channels
|
a. Pars
b. Channels c. Conventionals d. Cans |
|
76. When creating windows on the touchscreens of the Grand MA consoles, you have four categories available to you. Which one shows you information? (ex: what your fixtures are doing.)
|
C. Sheet
|
a. Preset
b. Pool c. Sheet d. Other |
|
77. Which category of window deals with fixture parameters? (ex: Pan/Tilt, Color, Gobo.)
|
A. Preset
|
a. Preset
b. Pool c. Sheet d. Other |
|
78. The “Clock” window is an example of this category of window.
|
D. Other
|
a. Preset
b. Pool c. Sheet d. Other |
|
79. This category of window will be where things get stored. (ex. Groups, Sequences)
|
B. Pool
|
a. Preset
b. Pool c. Sheet d. Other |
|
80. To clear a touchscreen, you press the ____________.
|
B. Top and Bottom Macro/View buttons
|
a. Delete key
b. Top and bottom Macro/View buttons c. Top Macro/View button while holding the delete key d. Clear key |
|
81. When you store a sequence to an executor fader on the Grand MA, where does that information actually get stored?
|
B. Sequence Pool
|
a. Fader page
b. Sequence pool c. File server d. Groups pool |
|
82. By default, what does the TOP button on every executor fader do?
|
A. Off
|
a. Off
b. Go c. On d. Go Back |
|
83. By default, what does the MIDDLE button on every executor fader do?
|
B. Go
|
a. Off
b. Go c. On d. Go Back |
|
84. By default, what does the BOTTOM button on every executor fader do?
|
C. On
|
a. Off
b. Go c. On d. Go Back |
|
85. This button turns off the output of the programmer side of the desk, but leaves on the output of the playback side of the desk.
|
C. Blind
|
a. Highlight
b. Black Out c. Blind d. Clear |
|
86. This button brings the intensity of a fixture to full, but removes all color information.
|
A. Highlight
|
a. Highlight
b. Black Out c. Blind d. Clear |
|
87. If you select a fixture, bring it’s dimmer to full, change it’s color to red, put it on the drum riser, and then Press (STORE) and select an empty cell in your Pan/Tilt preset window, what information did you store?
|
C. Pan and Tilt Values
|
a. Dimmer, color, pan and tilt values
b. Color values c. Pan and tilt values d. Nothing |
|
88. When storing a cue on the Grand MA, by default, only the “active” values will store. On your fixture sheet, what color are the cells that contain “active” values?
|
D. Red
|
a. Blue
b. Grey c. White d. Red |
|
89. To select a fixture using the keypad on the console, you need to press the (Fixture) button, and then type in the fixture’s ______ number, followed by (ENTER).
|
A. I.D.
|
a. I.D.
b. DMX c. Channel d. Serial |
|
90. On a fully loaded universe of data, how many updates can be sent to each of the 512 parameters per second?
|
B. 44
|
a. 256
b. 44 c. 128 d. 8 |
|
91. The “LAMP ON” command for a Mac fixture is found on the ______ channel.
|
C. Strobe (Shutter)
|
a. Dimmer
b. Pan c. Strobe (shutter) d. Effects |
|
92. Sending a _________ command to a Mac fixture will make the fixture re-align all of it’s motors and wheels back to a home position. This can sometimes be used to correct a fixture that may have slipped out of position. (Ex. – the fixture is supposed to be in blue, but is actually in red, because the motor controlling color lost it’s position)
|
B. Reset
|
a. Lamp Off
b. Reset c. Lamp On d. Man |
|
93. Why would we want to lamp off our fixtures at the end of the night, instead of just turning off the power to them?
|
B. To allow the fans to cool the fixture
|
a. It causes a nice fade out effect at the end of the show
b. To allow the fans to cool the fixture c. To keep the dmx line from feeding back d. To be able to unplug the dimmer rack |
|
94. If you need to access the parameters of a Mac fixture (ex. Dimmer, color, pan, tilt), but you do not have a console hooked up, what LCD Menu would you need to access on the fixture?
|
B. MAN
|
a. ADDR
b. MAN c. PSET d. INFO |
|
Quiz #2
1. How many circuits does a socapex cable carry? |
a. 6
|
a. 6
b. 12 c. 18 d. 19 |
|
2. How many channels make up one universe of DMX?
|
c. 512
|
a. 255
b. 256 c. 512 d. 8 |
|
3. How many steps exist in one channel of DMX?
|
c. 256
|
a. 8
b. 255 c. 256 d. 512 |
|
4. The DMX standard calls for a ___ pin XLR connector.
|
a. 5
|
a. 5
b. 3 c. 7 d. 19 |
|
5. At the end of a DMX data line, a ___ is used to limit DMX reflections.
|
a. Terminator
|
a. Terminator
b. Opto-Splitter c. Y-cable d. Transformer |
|
6. As per the rules of DMX, no more than ___ devices may be run on one un-split line.
|
b. 32
|
a. 8
b. 32 c. 256 d. 512 |
|
7. If you need to run more fixtures than the maximum allowed on one un-split line, you may use a __________.
|
b. Opto-Splitter
|
a. Terminator
b. Opto-Splitter c. Y-cable d. Transformer |
|
8. We commonly use 3 Phase power to supply our lighting systems. How many hot legs exist in a 3 phase system?
|
c. 3
|
a. 1
b. 2 c. 3 d. 5 |
|
9. In a 3 Phase system (in the U.S.), how many volts should your meter read between the Red connector and the Blue connector?
|
c. 208
|
a. 120
b. 0 c. 208 d. 240 |
|
10. In a 3 Phase system (in the U.S.), how many volts should your meter read between the Red connector and the Blue connector?
|
c. 208
|
a. 120
b. 0 c. 208 d. 240 |
|
11. If you have a main disconnect box labeled “3 Phase 200A 120V”, how many total amps can be supplied to your system?
|
a. 600
|
a. 600
b. 200 c. 120 d. 3 |
|
12. When connecting a 3 phase power system, what color connector do you plug in first?
|
a. Green
|
a. Green
b. White c. Black d. Red |
|
13. Who normally “ties in” the power to the main disconnect?
|
c. House Electrician
|
a. Dimmer Tech
b. Lighting Designer c. House Electrician d. Moving Light Tech |
|
14. “A user-programmable memory location that stores the value of a parameter” is the definition of what?
|
a. Group
|
a. Group
b. Cue c. Palette d. Sequence |
|
18. If you have a 48 channel 1.2K W dimmer rack, what size is the breaker on each dimmer?
|
b. 10 Amp
|
a. 5 Amp
b. 10 Amp c. 15 Amp d. 20 Amp |
|
19. Most moving lights use this type of lamp.
|
c. Arc
|
a. Incandescent
b. Fluorescent c. Arc d. LED |
|
20. What is a benefit of a moving head style fixture (as compared to a moving mirror)?
|
d. Greater Range of Motion
|
a. Faster Movement
b. More Colors c. Weighs Less d. Greater Range of Motion |
|
21. What is a drawback of a moving head style fixture (as compared to a moving mirror)?
|
c. Slower movement
|
a. Less gobos
b. Not as bright c. Slower movement d. Less Range of Motion |
|
22. The Technobeam is made by __________.
|
a. High End Systems
|
a. High End Systems
b. Vari-Lite c. Martin d. ETC |
|
23. If you want the color of white light from an arc source to match the color of white light from an incandescent source, you would put ___________ in the arc source fixture.
|
c. CTO (Correct to Orange) Filter
|
a. CTB Filter
b. 50% Magenta Filter c. CTO Filter d. Neutral Density Filter |
|
32. What type of filter do most moving lights use to change color?
|
b. Dichroic
|
a. Gel
b. Dichroic c. Douser d. Primary |
|
33. These types of color filters (See previous question) change the color of light by…
|
c. Reflecting the unwanted frequencies of the light
|
a. Absorbing the wavelengths not used
b. Changing the base frequency of the wavelength with power correction c. Reflecting the unwanted frequencies of the light d. Altering the lamp voltage |
|
34. Which of these is a secondary color of light?
|
c. Yellow
|
a. Blue
b. Green c. Yellow d. Red |
|
35. The compliment of the color Yellow is ___________?
|
a. Blue
|
a. Blue
b. Cyan c. Red d. Magenta |
|
36. The compliment of the color Magenta is __________?
|
a. Green
|
a. Green
b. Red c. Blue d. Cyan |
|
37. The Grand MA console terms moving lights as “fixtures”, and terms dimmers as “__________”.
|
b. Channels
|
a. Pars
b. Channels c. Conventionals d. Cans |
|
38. When creating windows on the touch-screens of the Grand MA consoles, you have four categories available to you. Which one shows you information? (ex: What your fixtures are doing)
|
c. Sheet
|
a. Preset
b. Pool c. Sheet d. Other |
|
39. Which category of window deals with fixture parameters? (ex: Pan/Tilt, Color, Gobo)
|
a. Preset
|
a. Preset
b. Pool c. Sheet d. Other |
|
40. This category of window will be where things get stored. (ex: Groups, Sequences)
|
b. Pool
|
a. Preset
b. Pool c. Sheet d. Other |
|
41. When you store a sequence to an executor fader on the Grand MA, where else does that information get stored?
|
b. Sequence pool
|
a. Fader page
b. Sequence pool c. File server d. Groups pool |
|
42. This button turns off the output of the programmer side of the desk, but leaves on the output of the playback side of the desk.
|
c. Blind
|
a. Highlite
b. Black Out c. Blind d. Clear |
|
43. This button brings the intensity of a fixture to full, but removes all color information.
|
a. Highlite
|
a. Highlite
b. Black Out c. Blind d. Clear |
|
44. When storing a cue on the Grand MA, by default, only the “active” values will store. On your fixture sheet, what color are the “active” values?
|
d. Red
|
a. Blue
b. Grey c. White d. Red |
|
45. The “LAMP ON” command for a Mac fixture is found on the ________ channel.
|
c. Strobe (shutter)
|
a. Dimmer
b. Pan c. Strobe (shutter) d. Effects |
|
46. Sending a __________ command to a Mac fixture will make the fixture re-align all of it’s motors and wheel back to a home position. This can sometimes be used to correct a fixture that may have slipped out of position. (Ex: The fixture is supposed to be in blue, but is actually in red, because the motor controlling color lost it’s position.)
|
b. Reset
|
a. Lamp Off
b. Reset c. Lamp On d. Man |
|
47. What does HTP stand for?
|
b. Highest Takes Precedence
|
a. High Temperature Parameter
b. Highest Takes Precedence c. Highlite to Pan d. Hold to Position |
|
48. Another term for LTP is ___________.
|
a
|
a. Vector
b. Tracking c. Moving d. Block |
|
61. Clear x1 on the Grand MA does what?
|
d. Clear Selection
|
a. Clear Active
b. Clear Preset c. Clear Release d. Clear Selection |
|
62. Clear x2 on the Grand MA does what?
|
a. Clear Active
|
a. Clear Active
b. Clear Preset c. Clear Release d. Clear Selection |
|
63. Clear x3 on the Grand MA does what?
|
c. Clear Release
|
a. Clear Active
b. Clear Preset c. Clear Release d. Clear Selection |
|
64. On the Grand MA, this is the default type of store.
|
a. Store Active
|
a. Store Active
b. Store All for Selected c. Store All d. Store Active for Selected |
|
65. On the Grand MA, this type of store stores all values for every fixture and channel in your show, regardless of what is selected.
|
c. Store All
|
a. Store
b. Store All for Selected c. Store All d. Store None for Selected |
|
66. By using a “Store All”, you are creating a _______ cue.
|
d. Block
|
a. Go
b. Off c. On d. Block |
|
72. On the Grand MA, to change the function of an executor button, you must first press the _____ key.
|
b. Assign
|
a. Move
b. Assign c. Delete d. Change |
|
73. Every cue in a sequence may have an overall fade or delay time associated with it. This is called the _______ timing.
|
b. Global
|
a. Parameter
b. Global c. Fixture d. Cue |
|
74. Every individual channel for each fixture may have it’s own fade or delay time associated with it. This is called _______ timing.
|
a. Parameter
|
a. Parameter
b. Global c. Fixture d. Cue |
|
84. If a cue has a 4 second delay, and a 3 second fade time, how many total seconds will this cue take to complete once it is triggered?
|
b. 7
|
a. 4
b. 7 c. 3 d. 1 |
|
85. This is NOT a trigger for a cue.
|
c. Sound
|
a. Follow
b. Go c. Sound d. Wait |
|
86. ____________ have specific fixtures associated with the effect. When you run this type of effect, it will automatically apply to the fixtures that were chosen for it when it was created, even if the fixtures are not selected at the time that the effect is started.
|
d. Assigned Effects
|
a. Un-assigned Effects
b. Selected Effects c. De-selected Effects d. Assigned Effects |
|
87. These types of effects (from the previous question) show up what color in the effects pool?
|
c. Pink
|
a. Yellow
b. Red c. Pink d. Blue |
|
88. When preparing gear for a show, many times we take multiple cables and tape them together into a single bundle. This is called a cable _______.
|
b. Loom
|
a. Tape
b. Loom c. Bridge d. Mess |
|
89. Why is it important to label and number trusses in our show?
|
b. So they are put together the same way every show
|
a. So we don’t lose them
b. So they are put together the same way every show c. So we know what order they go in the truck d. So we know how much weight they can hold |
|
90. When figuring out circuiting for the lights in our show, what is the first question that we need to ask?
|
b. What type of power do they need? (208 or 120)
|
a. What is the amp draw?
b. What type of power do they need? c. How many socapex cables do we have? d. What type of distro are we using? |
|
91. If you have 4 Mac 600’s, 5 Mac 500’s, and 15 par cans on one truss, how many socapex lines do you need to run to that truss?
|
c. 5 (15 - 120v lights need 3, 9 - 208v lights need 2)
|
a. 3
b. 4 c. 5 d. 6 |