Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
62 Cards in this Set
- Front
- Back
. Each pump impeller in a housing is called a
|
Stage
|
|
Pumps used as priming pumps are known as
|
Rotary / Gear
|
|
The spiral chamber in which the velocity given to water by the impeller is converted into pressure is called?
|
Volute
|
|
A _______________ valve is used to relive pressure in hose lines
|
Drain
|
|
A __________________ pump must be primed with an external priming device
|
Centrifugal
|
|
When priming, water enters the pump because ____________________
|
Atmospheric pressure forces it into the pump
|
|
A ____________________ gage is calibrated to read positive and negative pressures.
|
Compound
|
|
A _________________ valve opens when pressure rises above the high pressure.
|
Relief
|
|
Blades on an impeller are called
|
Vanes
|
|
A device that limits pressure surges is called a
|
Pressure Gov.
|
|
What type of flowmeter is maintenance free?
|
Spring Probe
|
|
What allows a truck to move and pump?
|
Power Take-Off
|
|
Centrifugal fire pumps may make use of what type of pressures
|
Positive Intake Pressures
|
|
The ____________________ system provides a circulating feed from several mains
|
Grid
|
|
The _________________________ supplies individual hydrants.
|
Distributor
|
|
______________________ is caused by corrosion and rust.
|
Encrustation
|
|
Pressure not used to overcome friction loss is called, ________________?
|
Residual
|
|
A hydrant with the largest capacity will be connected to a
|
Primary Feeder
|
|
Pressure created by a column of water due to elevation is know as _________________ pressure.
|
Head
|
|
Available flow from hydrants is estimated by determining the % drop between the _________________ and _________________ pressures.
|
Static and Residual
|
|
The part of total pressure not used to overcome friction or gravity while pushing water thru fire hose etc. is called _________________ pressure.
|
Residual
|
|
The operation in which each impeller of a centrifugal pump discharges into a common outlet is called,
|
Parallel
|
|
A good method for determining lift in a fire department is ….
For each _______ of vacume, water will rise _________ __________. |
One Inch, One Foot
|
|
When the flow thru a hose line rises from 100 gpm to 400 the FL rises ________ times.
|
16
|
|
________________ is used to find the flow pressure at a discharge opening.
|
Pitot tube and gage
|
|
17 inches of mercury on an intake gage= __________ ft. of lift.
|
17
|
|
Prior to changing from tank water to an external source make sure to do what?
|
Bleed the air
|
|
Which primer utilizes the ventui principle?
|
Exhaust Primer
|
|
If the priming device does not discharge water within ______ seconds for a 1500 gpm pumper, stop operation and check the trouble shooting procedures.
|
45 Seconds
|
|
When lowering a strainer into water to draft it must be placed at least _________ inches below the water.
|
18 inches
|
|
A 5in. hose would be expected to flow the same amount as ?
|
4 2 1/2 in. hoses.
|
|
When using 2 ½ or 3 in. hoselines to supply a pumper from a hydrant, lines can’t be longer than? _________________ feet
|
300 feet
|
|
NFPA requires a pump must pump it’s rated capacity at __________ feet of lift?
|
10 feet
|
|
What is the min. water depth in feet to draft from? ___________ feet
|
4 feet
|
|
Priming devices on centrifugal pumps are usually ?
|
Small positive displacement pumps
|
|
What are two types of relay pumping?
|
Max distance, and constant pressure
|
|
Relay operations should be shut down from the ________________ first.
|
Fire Scene
|
|
When relay pumping- the smallest pumper should be
|
... at the fire scene
|
|
The collapse zone around a building should be
|
1 to 1 1/2 times the height of the bld.
|
|
. Page 272 IFSTA says- When pumping to a standpipe system, a DE should allow ___________________ FL for the standpipe system itself.
|
24 psi
|
|
Pump pressures above ___________ psi may damage the standpipe system.
|
200 psi
|
|
When drafting the strainer should be placed _____ in. above the bottom to prevent whirl pooling.
|
12 inches
|
|
Maintain ____ psi to ____ psi on the discharge to avoid loosing a prime when nozzles are temporarily shut down.
|
30 to 40 psi
|
|
What is the max cutting force at the notch for the TNT Cutter?
|
109,098 psi
|
|
What is the weight of the TNT Cutter?
|
41 lbs
|
|
TNT Spreaders, what is the weight?
|
54.9
|
|
TNT Spreaders, what is the max spread force?
|
20,026 psi
|
|
TNT Ram, what is the weight?
|
46.3 lbs.
|
|
TNT Ram, what is the amount of the first push force?
|
51,500 lbs.
|
|
What is the air hammers normal operating pressure range?
|
150 / 200 psi.
|
|
When using the air hammer, when would you use the highest pressure and what is that pressure?
|
Cutting door hinges @ 250 psi
|
|
What are the air hammer’s blows per min.
|
2200 blows per min.
|
|
What is the air hammer’s length and weight?
|
10 inches / 5 lbs.
|
|
The __________ are used for modern car, van, truck and bus extrication.
|
T bits
|
|
_________ bits are specially designed for vehicle extrication
|
Curved
|
|
What is the first thing you should do if you are trapped in a structure?
|
Activate the emergency alert function of the portable radio
|
|
What is the third thing you should do if you are trapped in a structure?
|
Flashlight UP
|
|
88 cubic feet of air in an air cylinder will last you approx. ______ min?
|
60 min.
|
|
The three 9-volt batteries on the SEMS unit will last you approx. _____ hours
|
20 hours
|
|
The three-tone alarm is approx. ______ dba’s through the two speakers?
|
95 dba's
|
|
Once the PASS is activated it will sound for approx. _____ hours.
|
3 hours
|
|
The Scott Easy Flow regulator gives approx. _____ lpm of oxygen?
|
160 lpm's
|